Modern Manufacturing Technology and Equipment 2016 Issue 6 Design of the Assembly Point of the Bucket Rod of the Hydraulic Excavator

Design of the Assembly Point of the Bucket Rod of the Hydraulic Excavator
YANG Liu;

..............page:1-2,37

Study on Stress Characteristics of High Strength Steel and High Strength Teeth in Plastic Deformation
ZENG Juan;

..............page:3-4

Model Research on Heating Furnace under the Condition of Cold Boiler Seal
YUE Xiang;,WANG Yongqiang;,WANG AnLong;

..............page:5-6,26

Dynamic Equation and Modal Vibration Characteristic Analysis of Wind Power Gear Transmission System
LI Bin;,SHEN Yiping;,HAN Qingkai;

..............page:7-11

Fabrication and Tribological Properties of High Temperature Self-lubrication Composites
HAN Ying;

..............page:12-13,15

Fixture Design and Numerical Control Machining Process Techniques of Rocking Arm Body of Automobile Engine
LIU Jinwu;,HUANG Ke;,WU Mingyao;

..............page:14-15

Failure Analysis and Countermeasures for the Failure of the Main Contact of Electromagnetic Contactor
ZHANG Shuhong;

..............page:16-17,41

Ergonomics and Design of High Speed Railway Sleeper
XIE Quanyi;,ZHANG Yan;

..............page:18-20

Study on Influence Factors and Mechanism of Mechanical Seal Failure
Tuerdehule·Abudoula;,Adayi·Xieeryazidan;

..............page:21-22

Research on Temperature Field of Gear Form Grinding Between Different Grinding Conditions
ZHU Pengfei;,JIA Jia;

..............page:23-24

The Simplified Technique of Resistance Series Parallel Circuit
WU Wenbing;,XUN Xin;

..............page:25-26

Design of Solar Tracking System Based on Finel Lens
MA Guangtian;

..............page:27-30

Current Situation and Development Trend of Chemical Analysis Methods for Metal Materials
DING Yanguang;,BAI Kecai;

..............page:31-32,51

The Self-centering Collet Fixture Design
YAN Chunfeng;,ZHANG Xuechun;

..............page:33-34,69

Research on the Heat Transfer Characteristics of a Petroleum Coke Pot Calcining Furnace Bottom Plate Heat Exchanger
WANG Zuoren;,LIU Yongqi;,LV Jinsheng;,CAI Xiangyun;,WANG Yingfu;

..............page:35-37

Torsional Vibration Test Analysis of Marine Engine
ZOU ZuoMing;

..............page:38-41

Vertical Self-priming Pump Seal Flush and the Exhaust System Optimization Design
YU HaoJie;,WANG DaoChang;

..............page:42-43,60

For the New Energy Automotive Society Technology Domain Analysis and Promote the Transformation of Research
CHENG Weihua;

..............page:44-45

Side Suction Range Hood Power Control Design of Cap Injection Mold
CHENG Jingfan;,LIU Jintie;,YUAN Xiaohui;

..............page:46-47

Machining Process and Fixture Design for Special Hole
DAI Zhijie;,GAO Cailian;,ZHANG Jixiong;

..............page:48-49

Research on Product Assembly Process Generation and Information Integration Technology Based on Workflow
GAO Cailian;,ZHANG Jixiong;,SHI Jiangchuan;

..............page:50-51

Design of PWM Pulse Generator Based on HDL Verilog
HAN Wenqiang;,SONG Hongliang;,SANG Yunxiao;,YU Huiyong;

..............page:52-53,63

Research on Electric Control System of GMC16A Type Metro Grinding Train
LI Xiangli;

..............page:54-55,72

The Design and Application of the Flexible Packaging Lithium Battery Formation and Clamping Mechanism
LIU Hongmei;,FENG Yuan;,LU Huaimin;

..............page:56-56,58

Modular Design Method and Its Application in Mechanical Design
LIU Xianwei;

..............page:57-58

Study on the Design of Embedded Measuring Device for Cutting Coal and Rock in Coal Mining Machine
LUO Xingchen;,DONG Xuanxuan;

..............page:59-60

Design and Development of the Special Tool for the Spiral Milling of the Difficult Machining Materials
SHAO Fang;

..............page:61-63

Design and Development of EMU Repair Information Terminal System
WANG Zhongkai;,LV Fei;,CHEN Yan;

..............page:64-67

Research on the Basic Way and Trend of the Mainte-nance of 10kV~35kV Power Distribution Line
XU Gang;

..............page:68-69

Design and Research of Automobile Engine Air Distri-bution Mechanism
YANG Sheng;,LIN Chaogang;

..............page:70-70,98

Research and Development Mold CNC Machining Technology
YU Hongyu;,GUO Xiaoning;

..............page:71-72

Intelligent Vehicle Based on Embedded Design
ZHANG xiaoming;

..............page:73-74

Study on the Transformation of CNC Lathes Milling Integral Lathe
YING Fangzhi;

..............page:75-75,80

Design of a Pneumatic Brake Valve for Track Loco-motive
QI Xiaoxia;,WANG Zhaorong;

..............page:76-77,101

Research and Engineering Application on LWD Density QC Algorithm
WANG Changlong;,WANG Zhiming;,ZHANG Jiangtao;

..............page:78-80

Study on Numerical Simulation of Hot Extrusion Process of Automobile's Hollow Front Axle
WEI Guoqiang;,GUAN Yanjin;,ZHU Lihua;,XIE Zhendong;,SUN Depeng;

..............page:81-83

Development of Noise Signal Acquisition System Based on Virtual Instrument
WEI Yong;

..............page:84-85

Analysis on the Transmission Error of Floating Plate Involute Planetary Transmission with Small Tooth Number Difference
YANG Jie;,LI Luke;,ZHANG Ruizhu;

..............page:86-88

Practical Transformation and Exploration of Mold Maintenance Equipment
LIU Xiaoliang;

..............page:89-90

Research on Manufacturing Technology of Modular Joint and Central Axis of Dual Arm Robot
ZHANG Bo;,WU Zhenyong;,ZHOU Baoniu;

..............page:91-92

Development of Antenna Riveting Assembly Process Optimization System
QIAO Jiapeng;,XING Yan;,NI Jun;

..............page:93-94,96

Design of a New Type of Express Packaging Device
YANG Linjun;,ZHAO Qiang;,LI Kunming;,JING Xin;

..............page:95-96

Cause Analysis of Grinding Scratch on Cr17Ni4Cu4Nb Steel
YANG Hongchun;

..............page:97-98

Truss Arm Intersecting Line Welding Groove Cutting Technology Research
LIANG Wei;,GUO Yuzhao;,CHEN Lei;

..............page:99-101

The Improvement of High Silicon Iron Castings Pro-duction Process
SUI Jinmin;,GONG Sulian;

..............page:102-102,123

Technology of Plastic Injection Molding Automobile Parts Based on New Coating Free Composite Plastic Plate
CHENG Ke;

..............page:103-104

Manufacturing Technology and Development Trend of Metallurgical Machinery Gear Transmission Device
DUAN Deyi;

..............page:105-105,107

To Improve the Wear Strength Problem of Turbine Blade Erosion
FU Chao;

..............page:106-107

Method for Preparing Ceramic Composite Coating
LIU Naiqiang;,WU Xiude;,WEI Shizhong;,WU Liang;,WANG Xi;

..............page:108-109

On the Processing Technology of Engine Block
SHAO Qiujie;,JIANG Hangfeng;

..............page:110-110,118

Hydraulic Scaffolding Boring Process Applied to the Plane
WANG Hexian;,XU Songli;

..............page:111-112

Discussion on the Application and Management of Metal Cutting Fluid in Machining Process
ZHANG Jixiong;,DAI Zhijie;

..............page:113-113,125

Strain Hardening of Austenitic Stainless Steel Pressure Vessels
ZHAO Ziyan;

..............page:114-114,150

Prospect of Welding Technology and Equipment of Coal Fired Power Generation Boiler
ZHU Rongjie;

..............page:115-116

Recovery Methods of Two Kinds of Casting Defects After Finishing
HE Yingge;

..............page:117-118

Surface Quality and Precision Control Technology in Machining
HUI Xiaolao;

..............page:119-119,173

Design and Fabrication of Rotating LED Clock Based on Single Chip Microcomputer
JIANG Xinzhe;

..............page:120-121

Analysis of Intelligent Substation Process Layer Network Scheme
LI Dongmei;,WANG Ming;

..............page:122-123

The Noise of the Engine Intake System to Reduce the Inquiry
LIANG Hao;,XIANG Chenlong;

..............page:124-125

Process Reliability of Mechanical Manufacturing
LUO Lin;,GAO Guanghui;

..............page:126-126,141

The Planetary Differential Speed Mechanism Used in Crane Field Calculation and Analysis
NIU Tuo;

..............page:127-128

The Vibration Problem in Machining Analysis and Solutions
QIAN Shilin;

..............page:129-129,134

Parallel Circulation Suppression Strategy Based on Dis-tributed Control of Direct Drive Wind Power Generation
TAN Jiajie;

..............page:130-134

Analysis of the Causes of the Problem of Automobile Engine Idle Speed
WANG Xibin;

..............page:135-135,155

Discussion on the Relevant Problems in the Inspection of Explosion Proof Elevator
XIE Liuhui;

..............page:136-137

Analysis of Components and Influence of Control Rod Surface Oxidation Hongyanhe Nuclear Power Plant
YANG Xiaohuan;,TIAN Zhaohui;,LIU Jingjing;,DENG Pingjiu;

..............page:138-139,146

Analysis of Welding Quality Control in the Process of Chemical Equipment Manufacture
YE Linjun;

..............page:140-141

Analysis on Short Circuit Current and Relay Protec-tion Setting Calculation System of Power Plant
YUAN Ruiqin;,MENG Xuemeng;

..............page:142-143

Cause Analysis of Oil Leakage in A Subway Gear Box
ZHANG Jing;

..............page:144-146

The Vibration Sensing Performance Study on Half-coated Metal Core Piezoelectric Fiber(HMPF)
DING Yu;,LIU Rongrong;,HU Zhenyao;,YANG Jian;,LI Xianliang;,BOAM Yixiang;

..............page:147-150

An Improved Design of Overrunning Roller Clutch
ZHU Sheng;,LI Ping;,JING Jiang;

..............page:151-153

Application of Honeycomb Steam Seal in Medium and Small Steam Turbine
JIANG Lihong;,MAO Jixian;

..............page:154-155

The Motion Simulation and Analysis of Screw Driver Lightweight Palletizing Robot
YANG Qianming;,XUE Fangxi;,WANG Jianwei;

..............page:156-159

Analysis of Metal Selective Sintering 3D Printing Atmosphere Protection System
LI Jinliang;,WANG Hongbo;,ZHANG Kai;

..............page:160-160,166

Data Measuring Technology in Reverse Engineering
WANG Yun;

..............page:161-163,187

The Research and Design of Blanking Die Casting Products Nozzle Automatic Production Line Based on
HAN Xiurong;,LI Jianchun;,LIU Shengkang;

..............page:164-166

Development of Automatic Assembly Line for Solenoid Valve
SUN Guangfeng;

..............page:167-168

Discussion on Teaching Method Based on the Basic Deformation of the Component
WEI Hai;

..............page:169-169,191

Implementation of Special Process in the International Railway Industry Standard (IRIS)
ZHANG Yuanwang;

..............page:170-173

Discussion on the Construction of Urban Rail Vehicle Technology Specialty
ZHENG Yanping;,FU Huiqin;,XU Jian;

..............page:174-175

Discussion on the Teaching of Design Method and Design Steps of Modified Gear
SONG Guanying;,MENG Zhaoming;

..............page:176-178

Study on the Risk Assessment and Countermeasures of Research and Development Project Schedule
XU Xiaodong;,HAN Ying;

..............page:179-181,184

The Practice Research of Third-party Evaluation sys-tem for Work-integrated Learning Mode in Higher Voca-tional Training Quality
ZHENG Yong;

..............page:182-184

Process Management Research on Improve the Create Positions Internship of Basing on CRP Management System-As an Example with SuZhou Chien-shiung Institute of Technology
WANG Wen;,SHI Jianhao;

..............page:185-187

Electrical Design of Mitsubishi PLC and Frequency Control Based on Y7520W
SONG Yuqing;,SUN Xianliang;

..............page:188-189

Study on Optimization Strategy of Quality Management in the Field of Mechanical Processing Production
SHI Jiangchuan;,ZHANG Jixiong;

..............page:190-191

si da ji qi ren jia zu qi ju qing dao gao xin qu da zao chan ye hua ji di

..............page:-4--4

zhang gao li diao yan shen yang ji chuang he xin song ji qi ren guan zhu zhi neng zhi zao ban kuai

..............page:-5--5