1005-2895
2014 Issue 6
Contact Analysis of Cross Head Shaft and Hole of Thousand-Ton Plastic Injection Molding Machine
SHEN Xueming;,YI Guodong;,ZHANG Peng;
SHEN Xueming;,YI Guodong;,ZHANG Peng;
..............page:1-5
Topology Optimization of the Rear Platen in Fully Electric Injection Molding Machine
DING Dongsheng;
DING Dongsheng;
..............page:6-10
Numerical Simulation and Analysis of Internal Flow Characteristics for Centrifugal Fan of Sweepers
FU Ling;,LI Liang;,PENG Linbin;,XIAO Qinglin;,ZHANG Bin;,ZHANG Jin;
FU Ling;,LI Liang;,PENG Linbin;,XIAO Qinglin;,ZHANG Bin;,ZHANG Jin;
..............page:11-16
Vibration Model of Three-Foot Centrifuge
AN Wei;,CHEN Haiwei;,QIU Qingzhang;,WU Xiaoqing;
AN Wei;,CHEN Haiwei;,QIU Qingzhang;,WU Xiaoqing;
..............page:17-20
Study on Flow Characteristic of High Temperature Slag in Slag Cooler
CHEN Yali;,YANG Xuezhong;
CHEN Yali;,YANG Xuezhong;
..............page:21-24,28
Injection Mold Design for Phone Shell
HUANG Gang;,WANG Jinlian;
HUANG Gang;,WANG Jinlian;
..............page:25-28
Design of Angle-Interlock Fabric Loom
WANG Jingxin;,WANG Yuecun;,XU Weisong;
WANG Jingxin;,WANG Yuecun;,XU Weisong;
..............page:29-32
Fermentation Tank Agitator Strength Calculation Based on the Fluid Analysis
CHEN Tao;,DING Jianhua;,LI Weizhong;,LIU Yanlei;,MA Teng;,YANG Xiangyue;
CHEN Tao;,DING Jianhua;,LI Weizhong;,LIU Yanlei;,MA Teng;,YANG Xiangyue;
..............page:33-36,39
Orifice Effects on Dynamic Characteristics of Relief in Unloading Loop
SHI Lei;,ZHOU Yijie;
SHI Lei;,ZHOU Yijie;
..............page:37-39
Numerical Simulation of Safety Valve Opening Process Based on ANSYS CFX
MIN Jiafeng;,ZHU Haiqing;
MIN Jiafeng;,ZHU Haiqing;
..............page:40-43
Numerical Simulation of the Temperature Distribution in Heat Pipe Methanol Hydrogen Production Reactor
DENG Ang;,JIN Tianliang;,LIU Hui;,YU Bin;
DENG Ang;,JIN Tianliang;,LIU Hui;,YU Bin;
..............page:44-47
Welding Robot Design Based on Special Seam and Strength Analysis for Key Components
CHEN Dongdong;,LI Gen;,QIANG Hua;,ZHENG Tun;
CHEN Dongdong;,LI Gen;,QIANG Hua;,ZHENG Tun;
..............page:48-52
Vector Control for Induction Motor Based on dSPACE1005 Standard Board
LIU Qizi;,QIU Jianqi;,SHI Cenwei;
LIU Qizi;,QIU Jianqi;,SHI Cenwei;
..............page:53-57
Communication Between Sharky and Upper Computer Based on RS485
CHENG Wushan;,HU Xiaofei;
CHENG Wushan;,HU Xiaofei;
..............page:58-60
Frequency Control of Asynchronous Motor Based on PCI Bus
LI Xiaoqiu;,ZHANG Zhiming;
LI Xiaoqiu;,ZHANG Zhiming;
..............page:61-62
..............page:63-65,69
New Method to Calculate the Nonlinear Location Equations on Manipulator
DENG Chen;,DING Damin;,WANG Chaobin;,ZHANG Qinshun;
DENG Chen;,DING Damin;,WANG Chaobin;,ZHANG Qinshun;
..............page:66-69
Research on Accurate Segmentation Method of Sectional Data
ZHANG Haibo;,ZHANG Ran;,ZHANG Xu;
ZHANG Haibo;,ZHANG Ran;,ZHANG Xu;
..............page:70-73,77
New Equipment of Restriction of Cut Tobacco Length
HUA Gang;,LING Bin;,SUN Chao;,WU Weiguo;,ZOU Wei;
HUA Gang;,LING Bin;,SUN Chao;,WU Weiguo;,ZOU Wei;
..............page:74-77
Turning Process of PTFE Bellows
WU Yingchun;,XIE Bo;
WU Yingchun;,XIE Bo;
..............page:78-80
Structure Design of Magneto-Rheological Damper and Experimental Study on the Damping Characteristics
CHEN Haiwei;,QIU Qingzhang;,WU Xiaoqing;,ZHANG Qiuju;
CHEN Haiwei;,QIU Qingzhang;,WU Xiaoqing;,ZHANG Qiuju;
..............page:81-83,88
Calculation of Non-Conventional Heat Exchanger Tubes Natural Frequency
DONG Jinshan;,JIANG Xiaozhi;,L(U) Dongxiang;,WU Hang;,ZHANG Shuying;
DONG Jinshan;,JIANG Xiaozhi;,L(U) Dongxiang;,WU Hang;,ZHANG Shuying;
..............page:84-88
Device about Mechanical Tension Control
XIU Xueqiang;
XIU Xueqiang;
..............page:89-91
Limit on the Opening Spacing of Cylindrical Shell with Double Openings under Internal Pressure
HUANG Sai;,ZHOU Changyu;
HUANG Sai;,ZHOU Changyu;
..............page:92-96,100
Optimization of Process Parameters for Plastic Parts of Current Coil Frame Based on Orthogonal Experiment Method
FU Jiangang;
FU Jiangang;
..............page:97-100
Fluidity Improvement for Inlet Main Pipe of Heat Exchanger in Fumigation Oven
CHEN Feiqi;,CHEN Jiahong;,LIU Hong;,YANG Zheren;,ZHU Gaoyong;
CHEN Feiqi;,CHEN Jiahong;,LIU Hong;,YANG Zheren;,ZHU Gaoyong;
..............page:101-103
..............page:104-107
Improvement of Paving Platform of Rapid Prototyping Machine for Ceramic Parts
GAO Dongqiang;,SUN Qian;,WANG Wei;,ZHANG Xifeng;
GAO Dongqiang;,SUN Qian;,WANG Wei;,ZHANG Xifeng;
..............page:108-110
Design Optimization of Injection Molding Gate for Printer Board with Insert Based on Moldflow
HE Haiqin;,LI Yanping;,LIU Chengjuan;,WU Qiuping;
HE Haiqin;,LI Yanping;,LIU Chengjuan;,WU Qiuping;
..............page:111-115
Analysis and Improvement of Tobacco Blocking in the Cabinet Feeder Electronic Scale System
DAI Yuxin;,SHAO Zhu;
DAI Yuxin;,SHAO Zhu;
..............page:116-119
Review of Assessment and Buckling Researches on Dented Subsea Pipelines
HE Xuan;,JIN Zhijiang;,QIAN Feng;,YAN Sunting;,YE Hao;
HE Xuan;,JIN Zhijiang;,QIAN Feng;,YAN Sunting;,YE Hao;
..............page:120-125