1000-9345
2010 Issue 1
analysis and optimization on factors affecting forming quality of half axle gears warm precision forging
WANG Menghan;CHEN Xihou;ZHOU Jie
WANG Menghan;CHEN Xihou;ZHOU Jie
..............page:110-114
numerical and experimental investigation of high-efficiency axial-flow pump
SHI Weidong;ZHANG Desheng;GUAN Xingfan;LENG Hongfei
SHI Weidong;ZHANG Desheng;GUAN Xingfan;LENG Hongfei
..............page:38-44
innovation in the computing system of straightening force
CHEN Min;JIANG Xiaomin;ZHAO Zuxin;HUANG Xiaobo
CHEN Min;JIANG Xiaomin;ZHAO Zuxin;HUANG Xiaobo
..............page:115-121
effect of air injector on the performance of an air-lift for conveying river sand
TANG Chuanlin;HU Dong;PEI Jianghong;YANG Lin
TANG Chuanlin;HU Dong;PEI Jianghong;YANG Lin
..............page:122-128
modeling and analytical solution of chatter stability for t-slot milling
LI Zhongqun;LIU Qiang
LI Zhongqun;LIU Qiang
..............page:88-93
flow ripple of axial piston pump with computational fluid dynamic simulation using compressible hydraulic oil
MA Ji\'en;XU Bing;ZHANG Bin;YANG Huayong
MA Ji\'en;XU Bing;ZHANG Bin;YANG Huayong
..............page:45-52
leakage prediction method for contacting mechanical seals with parallel faces
SUN Jianjun;WEI Long;FENG Xiu;GU Boqin
SUN Jianjun;WEI Long;FENG Xiu;GU Boqin
..............page:7-15
measurement of attenuation of ultrasonic propagating through the thin layer media with time delay spectrum
WANG Xingguo;CHANG Junjie;SHAN Yingchun;TIE Shaodong;YAO Man;XU Jiujun
WANG Xingguo;CHANG Junjie;SHAN Yingchun;TIE Shaodong;YAO Man;XU Jiujun
..............page:129-134
numerical method based on compatible manifold element for thin plate bending
ZHANG Zhengrong;ZHANG Xiangwei;L(U) Wenge
ZHANG Zhengrong;ZHANG Xiangwei;L(U) Wenge
..............page:100-109
investigation on uniaxial tensile instability of usibor1500 steel sheets at elevated temperature
MIN Junying;LIN Jianping;TIAN Haobin;SUN Guohua;XU Zhou
MIN Junying;LIN Jianping;TIAN Haobin;SUN Guohua;XU Zhou
..............page:94-99
a new kind of pilot controlled proportional direction valve with internal flow feedback
QUAN Long;XU Xiaoqing;YAN Zheng;ZHANG Xiaojun
QUAN Long;XU Xiaoqing;YAN Zheng;ZHANG Xiaojun
..............page:60-65
particle image velocimetry measurement of the flow field in the play of the drilling pump valve
YANG Guoan;YIN Xin;SONG Zheng;HUANG Cong
YANG Guoan;YIN Xin;SONG Zheng;HUANG Cong
..............page:27-37
experimental research on salt-out particle motion and concentration distribution in a vortex pump volute
GAO Bo;YANG Minguan
GAO Bo;YANG Minguan
..............page:53-59
numerical research on performance prediction for centrifugal pumps
TAN Minggao;YUAN Shouqi;LIU Houlin;WANG Yong;WANG Kai
TAN Minggao;YUAN Shouqi;LIU Houlin;WANG Yong;WANG Kai
..............page:21-26
motion planning algorithms of redundant manipulators based on self-motion manifolds
YAO Yufeng;ZHAO Jianwen;HUANG Bo
YAO Yufeng;ZHAO Jianwen;HUANG Bo
..............page:80-87
improvement on on-line ferrograph image identification
WU Tonghai;WANG Weigang;WU Jiaoyi;MAO Junhong;XIE Youbai
WU Tonghai;WANG Weigang;WU Jiaoyi;MAO Junhong;XIE Youbai
..............page:1-6
fuzzy hybrid control of vibration attitude of full carvia magneto-rheological suspensions
LI Rui;CHEN Weimin;LIAO Changrong;DONG Xiaomin
LI Rui;CHEN Weimin;LIAO Changrong;DONG Xiaomin
..............page:72-79
lifetime evaluating and the effects of operation conditions on automotive fuel cells
PEI Pucheng;YUAN Xing;LI Pengcheng;CHAO Pengxiang;CHANG Qianfei
PEI Pucheng;YUAN Xing;LI Pengcheng;CHAO Pengxiang;CHANG Qianfei
..............page:66-71
design and fabrication of mems gyroscopes on the silicon-on-insulator substrate with decoupled oscillation modes
XIE Jianbing;YUAN Weizheng;CHANG Honglong
XIE Jianbing;YUAN Weizheng;CHANG Honglong
..............page:16-20