Journal of Jilin University(Engineering and Technology Edition) 2006 Issue 2 Heat supplying system by urban sewage heat energy based on platistic-Al-pipe-improved

Heat supplying system by urban sewage heat energy based on platistic-Al-pipe-improved
Bai Li;Yin Jun;Liao Zi-sheng

..............page:269-273

Analysis of influence factors of greenness of bionic terrain machinery based on DEMATEL approach
Li Hong-wei;Yang Yin-sheng

..............page:274-278

Empirical research on process-based-view valuation approach of venture
Cai Li;Wang Yun-mei

..............page:279-284

an ei yao qiu zhuan xie zhong ying wen zhai yao

..............page:封三

Batch experiment on reduction of nitrate in water by nanoscale zero valent iron particles
Li Tie-long;Liu Hai-shui;Jin Zhao-hui;Kang Hai-yan;Liu Zhen-ying;Wang Wei

..............page:264-268

Fast extracting and tracking of target in complex environment
Hao Zhi-cheng;Zhu Ming;Liu Wei

..............page:259-263

EVM measurement algorithm for TD-SCDMA UE conformance test based on iterative process
Jin Lei;Wang Bing;Li Chun-yuan;Zhang Ping

..............page:253-258

Design and performance analysis of labeling map methods for BICM-ID
Gong Feng-kui;Ge Jian-hua;Li Bing-bing;Liu Peng

..............page:247-252

Automatic guided vehicle system based on localization and navigation by ultrasonic and infrared ray
Yan Xue-zhi;Wang Shu-xun;Ma Zhong-sheng;Li Xin

..............page:242-246

Single-cable checking system for time-lapse marine seismic data acquisition and recording system
Cheng Jing-yuan;Song Ke-zhu;Yang Jun-feng

..............page:237-241

Robot assisted intramedullary interlocking nail system
Wu Dong-mei;Du Zhi-jiang;Sun Li-ning

..............page:232-236

Novel selective reset CMOS image sensor circuit structure
Zhou Jin;Yao Su-ying;Xu Jiang-tao;Hu Yan-xiang

..............page:227-231

Network monitor based on NDIS intermediate driver
Yang Zhi-jun;Tian Di;Zhou Bin

..............page:224-226

Structure and operation model of graphic language
Xie Xuan-song;Sui Yang-yi;Lin Jun

..............page:219-223

Influence of starting notch geometry parameters of connecting rod on its fracture splitting force
Yang Shen-hua;Zhang Zhi-qiang;Kou Shu-qing

..............page:195-198

Experimental analysis of roller burnishing process for metal plane
Song Yu-quan;Xu Zhen-guo;Zhao Po;Liu Ying

..............page:188-194

Simulation-based assessment of variable message signs route guidance information under congestion condition
Jiang Gui-yan;Zheng Zu-duo;Bai Zhu;Dai Lei-lei;Zhao Jia-qi

..............page:183-187

Improvement of entrance configuration in plate-fin heat exchanger
Wen Jian;Li Yan-zhong;Zhou Ai-min;Zhang Ke

..............page:177-182

Underground heat transfer characteristics in discontinuous operation of GSHP and its control strategy
Cui Shu-qin;Gao Qing;Li Ming;Jiang Yan

..............page:172-176

Open architecture of automotive E/E control system based on quantum frame
Li Hong-bin;Zhang Cheng-rui

..............page:166-171

Power performance of rear wheel drive vehicle with disk-type mechanical limited-slip differential
Wang Jian-hua;Wang Yun-cheng;Fu Tie-jun;Zhang Bao-sheng

..............page:161-165

Setup of vehicle longitudinal dynamic model for adaptive cruise control
Zhan Jun

..............page:157-160

Active control during shifting in hybrid electric vehicle
Liu Zhi-ru;Wang Qing-nian;Wang Guang-ping

..............page:153-156

Ni-P deposits and non-chromate pretreatment technology on magnesium alloy
Niu Li-yuan;Li Guang-yu;Jiang Zhong-hao;Sun Li-ping;Han Dong;Lian Jian-she

..............page:148-152

MiCrostructure and mechanical property of 65Mn steel after severe plastic deformation
Du Zhong-ze;Huang Jun-xia;Fu Han-guang;Wang Jing-tao;Zhao Xi-cheng

..............page:143-147

Influence of typical poultry feather structure and surface lipoid on wettability
Ren Lu-quan;Shang Guang-rui;Yang Xiao-dong

..............page:213-218

Polishing die free-form surface by series and parallel polishing machine
Lin Jie-qiong;Zhao Ji;Wang Yi-qiang;Zhu Pei-xing

..............page:209-212

Intelligent prediction and control system of shaft workpiece size in cylinder traverse grinding
Wang Jia-zhong;Wang Long-shan;Li Guo-fa;Zhou Gui-hong;Ding Ning

..............page:204-208

Method of internal 3-D flow field numerical simulation for hydrodynamic torque converter
Zhao Ding-xuan;Shi Xiang-zhong;Shang Tao

..............page:199-203