0449-749X
1999 Issue 4
RESEARCH ON HOT-ROLLING SCHEDULING FOR TUBE PRODUCTION
TANG Lixin;ZHANG Guofan;YANG Zihou;WANG Mengguang
TANG Lixin;ZHANG Guofan;YANG Zihou;WANG Mengguang
..............page:74-76
"3H AND 2L"--THE DIRECTION OF DEVELOPMENT OF EAF STEELMAKING TECHNOLOGY
LI Shiqi;LIU Runzao;LIU Huaiyu;LAN Denian;GUO Zheng;HOU Zhenduo;JIANG Hengsheng
LI Shiqi;LIU Runzao;LIU Huaiyu;LAN Denian;GUO Zheng;HOU Zhenduo;JIANG Hengsheng
..............page:69-73
SIGNAL ANALYSIS AND PROCESSING IN EDDY CURRENT DETECTION OF STEEL
JIA Huiming;GE Weiliang
JIA Huiming;GE Weiliang
..............page:65-68
NUMERICAL SIMULATION IN ELECTROSLAG ROLL CLADDING EQUIPMENT DESIGNING
WU Chunjing;SHEN Dingzhao;YANG Guoming;JIA Tiancong;HUANG Yongxi;LIANG Jin;LIU Di
WU Chunjing;SHEN Dingzhao;YANG Guoming;JIA Tiancong;HUANG Yongxi;LIANG Jin;LIU Di
..............page:61-64
STUDY ON RELATION BETWEEN AXIAL RIGIDITY AND AXIAL ASSEMBLY PART MATCHING OF GY TYPE MILL
ZHONG Jianyu;HOU Jianxin;YAN Fengrong
ZHONG Jianyu;HOU Jianxin;YAN Fengrong
..............page:58-60
..............page:56-57
SMITH PREDICTIVE METHOD WITH FUZZY SELF-ADJUSTING FOR TIME-DELAY SYSTEM
HAN Rucheng;LI Xiaofeng;WANG Yahui
HAN Rucheng;LI Xiaofeng;WANG Yahui
..............page:52-55
LOW CARBON Si-Nb DUAL-PHASE STEEL WIRES FOR WEAR-RESISTANT SCREENS
SUI Xiaohong;ZHAO Xiaoping;BIAN Zhongrui
SUI Xiaohong;ZHAO Xiaoping;BIAN Zhongrui
..............page:48-51
PHASE EXAMINATION OF HEAT RESISTANT CENTRIFUGALLY CAST ALLOY TUBES
FU Hongzhen;WANG Yanqing;ZHANG Xuyao;JIAO Lanying;YANG Jing;YE Maosheng
FU Hongzhen;WANG Yanqing;ZHANG Xuyao;JIAO Lanying;YANG Jing;YE Maosheng
..............page:43-47
MICROSTRUCTURE AND PROPERTIES OF 65MnV USED FOR WHOLE QUENCHED EJECTOR PINS OF PLASTIC DIES
XU Daqing;ZHAO Jiansheng;CHENG Yuhang;CHEN Yuqiu
XU Daqing;ZHAO Jiansheng;CHENG Yuhang;CHEN Yuqiu
..............page:40-42
STUDY ON STRUCTURE INHERITANCE REMOVING BY AUSTENITE RECRYSTALLIZATION FOR 26Cr2Ni4MoV ROTOR STEEL
CUI Zanquan
CUI Zanquan
..............page:37-39
MODELING THE META-RECRYSTALLIZATION OF Q235
DOU Xiaofeng;LU Shouli;ZHAO Hui;ZHANG Peng
DOU Xiaofeng;LU Shouli;ZHAO Hui;ZHANG Peng
..............page:34-36
IMPLEMENTATION OF OPTIMIZED ROLLING SCHEDULE WITH MULTIPLE SUBSCHEDULES BY ELECTROMECHANICAL SCREWDOWN
BAI Aimin;PEI Xiaodong;ZHANG Jinzhi;ZHAO Jixiu;OUYANG Yu
BAI Aimin;PEI Xiaodong;ZHANG Jinzhi;ZHAO Jixiu;OUYANG Yu
..............page:30-33
..............page:24-29
INCLUSION MODIFICATION IN SPRING STEEL PRODUCTION
LI Zhengbang;XUE Zhengliang;ZHANG Jiawen
LI Zhengbang;XUE Zhengliang;ZHANG Jiawen
..............page:20-23
THE EXPERIMENTAL STUDY OF THE MOULD DYNAMIC FRICTION FORCE IN CONTINUOUS CASTING OF STEEL
GAN Yong;CHEN Dongliang;YANG Wengai
GAN Yong;CHEN Dongliang;YANG Wengai
..............page:16-19
TIME FACTOR ANALYSIS OF TWO-HEAT SEQUENTIAL CASTING AT NO.1 EAF STEELMAKING PLANT OF GUANGZHOU IRON & STEEL CO., LTD.
TANG Honghua;TIAN Naiyuan;LIU Qing;LI Liejun;TONG Dongmin
TANG Honghua;TIAN Naiyuan;LIU Qing;LI Liejun;TONG Dongmin
..............page:12-15
BELL-LESS TOP EQUIPMENT MODEL OF TIANJIN IRON WORKS FOR SMALL AND MIDDLE BLAST FURNACES
LI Chaojin;MA Jianguo
LI Chaojin;MA Jianguo
..............page:9-11
THE HOT TEST STUDY ON THE STAVE OF BAOSTEEL′S NO.3 BLAST FURNACE
CAO Chuangen;ZHOU Yusheng;CAO Jin;CHEN Haiyong;CANG Daqiang
CAO Chuangen;ZHOU Yusheng;CAO Jin;CHEN Haiyong;CANG Daqiang
..............page:4-8
SINTER PRODUCTION WITH WASHED COAL AS FUEL INSTEAD OF RAW COAL
LI Lijian;GAO Bingyin
LI Lijian;GAO Bingyin
..............page:1-3