1006-2807
2014 Issue 2
Analysis on the Test Results of the QFSN 1 100 MW-class Nuclear Power Turbine Generator
LI Zhi;,LIANG Xubiao;,SHENG Minghua;,SHU Wuqing;,TANG Qiang;,WANG Tingshan;
LI Zhi;,LIANG Xubiao;,SHENG Minghua;,SHU Wuqing;,TANG Qiang;,WANG Tingshan;
..............page:1-3,11
Method to Decrease Cogging Torque of PM Synchronous Motors with Concentrated Windings
CHEN Li;,LAI Haojie;,LIU Gong;
CHEN Li;,LAI Haojie;,LIU Gong;
..............page:4-7
Calculation and Analysis on Strength of the Rotating Shaft of the Specialized High-efficiency Motor for Large-size Blowers
CHEN Lin;,TANG Huiming;
CHEN Lin;,TANG Huiming;
..............page:8-11
Calculation of Stator Current Fluctuation and Selection of Flywheel Torque of the Synchronous Motor to Drive the Compressor
CHEN Xingwei;
CHEN Xingwei;
..............page:12-15
Research on the Vibration Mode of the Fixed-structure of Stator Winding Ends of the Four-pole Turbo-generator
HU Jianbo;,LI Zhi;,LIANG Xubiao;,LIU Wenbo;,WU Xinya;,XIAN Zhelong;
HU Jianbo;,LI Zhi;,LIANG Xubiao;,LIU Wenbo;,WU Xinya;,XIAN Zhelong;
..............page:16-18
Modeling and Simulation of the Excitation System of the Synchronous Generator Based upon Self-tuning PID Control
CHU Wenhao;,WANG Ting;
CHU Wenhao;,WANG Ting;
..............page:19-22
Loss Analysis of Induction Motor of Different Open-phase Operating Statuses
CUI Xueshen;,LI Wenzhi;
CUI Xueshen;,LI Wenzhi;
..............page:23-27
..............page:28-29
Briefly Introduce How to Increase the YB3 Explosion-proof Three-phase Asynchronous Motor Efficiency
GU Zhirong;,HE Shengqiang;
GU Zhirong;,HE Shengqiang;
..............page:30-32
Solving Confliction Problem Between the Gas Turbine Generator Seal-oil System and Building Steel Structure
CHEN Wenfei;,YANG Chengzuo;
CHEN Wenfei;,YANG Chengzuo;
..............page:33-34
..............page:35-36,39
Manufacture Technology of Stator Frame of the 1 250 MW Nuclear Power Turbine Generator
GAN Hongfeng;
GAN Hongfeng;
..............page:37-39
..............page:40-41,44
Introduction of Two Mechanic Over-load Protective Units for Electric Motors
GOU Junshan;,HUANG Xinyu;,LI Baofeng;
GOU Junshan;,HUANG Xinyu;,LI Baofeng;
..............page:42-44
Analysis on the Technological Difficulties in Machining the Shaft of the Large-size Wind Turbine Generator
DING Liguo;,WANG Yanfang;
DING Liguo;,WANG Yanfang;
..............page:45-47,50
Measurement of Thermal Conductivity of the Main Insulation of Stator Windings in the Turbine Generator
ZHU Huiying;
ZHU Huiying;
..............page:48-50
Rotor Assembly Process of the 5 800 kW Brushless Exciter
QIAO Xiuxiu;,ZHOU Zhenfu;
QIAO Xiuxiu;,ZHOU Zhenfu;
..............page:51-53
Motors’ Rolling Bearing and Its Lubricant Grease as Well as Prevention from Bearing Failure
CHEN Jingang;
CHEN Jingang;
..............page:54-56,57
Dimensional Calculation of the Wound Model for Single-double Layer Unequal-turn Sine Windings
CAO Ting;,SU Qiping;,WU Dan;
CAO Ting;,SU Qiping;,WU Dan;
..............page:57-58
A Kind of Shaft Seal Assembly of the Electric Motors
OU Jiaxiang;,RUAN Jinjing;,WANG Jun;
OU Jiaxiang;,RUAN Jinjing;,WANG Jun;
..............page:59-59,64
Technological Introduction on Braze Welding Between Stator Bars of the 1 000 MW Ultra-supercritical Turbine Generator
DU Jincheng;
DU Jincheng;
..............page:60-62
..............page:63-64