Foundry Technology 2009 Issue 7 Experimental Observation of the No-contact Electromagnetic Shaping for the Pure Aluminum Melt

Experimental Observation of the No-contact Electromagnetic Shaping for the Pure Aluminum Melt
an wei ; liu lin ; fu heng zhi

..............page:871-875

Performance of Risers Covering Flux for Large Castings
pang fu wei ; wang ai qin ; xie jing pei ; wang wen zuo

..............page:853-856

Production Technique on theIndefinite Knife Finger Prepared by Malleable Cast Iron
yu yong zhi ; qi fu ren

..............page:959-960

Application of Pro/E Curved Surface Modeling in ProCAST Mesh Generation
wang bao shun ; dong jian xin ; zhang mai cang ; zheng lei

..............page:926-928

Effect of Heat Treatment on the Microstructure and Properties of ZG42Cr2MnSiMoRE Steel
jia yu feng ; xie jing pei ; wang wen zuo ; wang ai qin ; li luo li ; zhou li gang ; liu zuo

..............page:868-870

Technical I mprovement of MAN074-type Speed Reducer Shell
li xiao peng

..............page:954-955

Effect of Cooling Rate on Microstructure and Solidification Mode in Cr15Mn9Cu2Ni1N Austenitic Stainless Steel
zhu liang ; liang xin bin

..............page:864-867

Microstructure and Antibacterial Properties of Antibacterial Martensite Stainless Steel
zhang an feng ; li li jun ; qiao ji ying ; ai li

..............page:860-863

xing ye qi ye shi chang

..............page:843-848

Influence of FS Powder on the Properties of the Molding Sand
wu cheng long ; zhu qi lin ; wang yue ; jin yong ; xi zuo ; mei yong

..............page:952-953

Centrifugal Casting For Small-diameter Sleeve and Ring Parts prepared by Stainless Steel
li xi hong ; wang xian rong

..............page:953-954

Welding Hot Crack of Low Temperature Valve
shi jiu yang ; zhang zhi yong

..............page:964

Development of Riser System CAD Software for Steel Casting based on Pro/E
wang zhi ping ; pei xiao liang ; zhu chang sheng ; lu yang

..............page:849-852

Effect of Ultrasonic Vibration Parameter on Solidification Structure of Al-1%Si Alloy Ingots under Melt Holding
jia zheng ; li jun wen ; jiang feng ; chen chao ; zuo wan fu ; fu ying

..............page:899-903

Effect of Nitriding-sulfurizing Composite Treatment on Tribological Behavior of Titanium Alloy
wang li jie ; wang hong bo

..............page:908-910

Micro Hardness Analysis for Micro-arc Oxidation(MAO) Films on AZ91D Die-casting Magnesium Alloy
chen hong ; hao jian min

..............page:911-914

Regression Equation of Grey Cast Iron Tensile Strength Chemical Composition and Chill Width for Triangle Test Tables
wang feng juan

..............page:957-959

Practice of Full Mould Casting Technology for Large-sized Plate Castings
sun chang fu ; shao juan

..............page:956-957

Property and Oxidize Behavior of Thermal Spraying Mo Coating
jiang chao ping ; chen hong ; hao jian min

..............page:915-917

Research Trend of Nanostructured WC-Co Coating
liu sheng lin ; zheng xue ping

..............page:918-921

Microstructures and Wear Properties of In-situ AlN Reinforced Magnesium Composites
wang qiang ; yuan sen ; wang wu xiao ; xing shu le ; wang xin xin

..............page:876-879

Experimental Study of Selective Laser Sintering Forming Accuracy on the Plastic Powder
cui jian fang ; wang zhen rong ; bai pei kang

..............page:939-941

Casting Process Designs and Production Control of260Cylinder Block
yang chuan dong ; chen xian jun ; wang le cheng ; xu huan lei ; lei qi hui

..............page:949-950

Crack and Air Hole of Anode Mould Produced by Copper Cathode
zhao da jun ; tang li ; zhang kun hua

..............page:963

Production of Lightloving Species Pole Prepared by DuctileIron
ying hao ; pan dong jie

..............page:950-951

Research on the Fracture Performance of Zn-Al-Si Alloys
you zhi yong ; zhao hao feng ; li jian chun ; wei ai li

..............page:892-895

Technics Progress on the Purification of Solar Grade(SoG) Silicon by Plasma
luo da wei ; liu ning ; lu yi ping ; li ting ju ; zhang guo liang

..............page:945-948

Twin Rolls Thin Strip Continuous Casting Technology
cheng ting yu ; zheng feng ; xu shao bing

..............page:896-898

In-situ Reaction Formation of TiB_2 Particles and the Effect of TiB_2 Particles on the Mechanical Properties of Al-Si-Mg Alloy
cui qing ling ; wang ming xing ; pang jin hui ; liu zhi yong ; liu zhong xia ; song tian fu

..............page:888-891

Melting Technique of High-strength Grey Cast Iron by MediumFrequency Furnace
yang chun lei

..............page:964

Optimization of Casting Technology and Practice Verification for Running Wheel
zhou you ; ding ze yu

..............page:857-859

Friction and Wear Characteristics of AZ91D Magnesium Alloy Formed by Rheo-diecasting and Die Casting Process
li dong nan ; fan you fa

..............page:880-883

Numerical Simulation of Protective Gas in the Furnace of Magnesium Melt
ying fu qiang ; wang cong cong

..............page:884-887

Research Status in Fabrication and Failure of Thermal Barrier Coatings
xing ya zhe ; hao jian min

..............page:922-925

Influence of Brightener Content on the Electroless Deposit Ni-P Coatings for ZL101 Aluminum Alloy
li xue song ; wu yi ; wu hua

..............page:929-932

Temperature Dependent Internal Friction Characteristic and Solute Effect of High Damping Magnesium Alloys
wan di qing ; yang gen cang ; wang jin cheng

..............page:904-907

Practical Research on the Corrosion Resistance Effect of External Pipe Prepared by Ductile Iron
wu jian wei ; wang hai ling

..............page:933-935

Design of Injection Systerm of Lost Foam Casting under Negative Pressure
zhu li juan ; zhou yuan ; wang ming na ; zhang yu ; dong xiu qi

..............page:942-944

Forming Course of Polyimide Composite Materials
wang zuo ; dong yuan peng ; di bao qing

..............page:936-938

Digital Design and Manufacture of Full Mold Casting Pattern for Vehicle Body Punch Die
xiang xiong fang

..............page:961-962