1001-0777
2016 Issue 5
Present situation, development and prospect of low-magnification inspection technology for steel billet
WANG Hong-liang;,ZHOU Li-min;,ZHOU Li-fu;,WANG Ke-jie;
WANG Hong-liang;,ZHOU Li-min;,ZHOU Li-fu;,WANG Ke-jie;
..............page:1-7
Influence of carbon content on the mechanical properties of BTC1 cold-roll enamel steel after enamel firing
LI He-tian;,ZHANG Shao-zong;,FANG Jian;
LI He-tian;,ZHANG Shao-zong;,FANG Jian;
..............page:8-11
..............page:11,40
Production of biological-friendly stainless steel and its application in watch products
WENG Jian-yin;,NING Xiao-zhi;,DONG Han;,LI Bei;,BAO Xian-yong;
WENG Jian-yin;,NING Xiao-zhi;,DONG Han;,LI Bei;,BAO Xian-yong;
..............page:12-16
Evolution law of cold rolling texture in thickness direction for ferrite stainless steel sheet
HE Tong;,DU Juan;,LIU Yan-dong;
HE Tong;,DU Juan;,LIU Yan-dong;
..............page:17-22
Discussion on dynamic failure load of spot-welded joint for high-strength steel
ZHU Hong-chuan;,WANG You-lu;,WU Qing-song;,HU Yin-hong;,WEI Xing;,YANG Bing;
ZHU Hong-chuan;,WANG You-lu;,WU Qing-song;,HU Yin-hong;,WEI Xing;,YANG Bing;
..............page:23-27
Influence of Nb on the mechanical properties of galvanized dual phase steel
LIANG Xuan;,LIU Zai-wang;
LIANG Xuan;,LIU Zai-wang;
..............page:28-31
Discussion on reliability improvement of online eddy current testing for stainless steel tubes
ZHANG Jian-long;,ZHANG Jie;,ZHU Guo-qing;
ZHANG Jian-long;,ZHANG Jie;,ZHU Guo-qing;
..............page:32-36
Failure analysis of hot oil pump shaft of 1Cr17Ni2 steel
YI Hai-feng;,HUANG Li-jun;,YI Fei;,GE Xiao-xiao;
YI Hai-feng;,HUANG Li-jun;,YI Fei;,GE Xiao-xiao;
..............page:37-40
Cause analysis of flattening fracture of welded pipes
ZHANG Da-fu;,WU An-shu;,LIU Jin-yan;
ZHANG Da-fu;,WU An-shu;,LIU Jin-yan;
..............page:41-45
Cause analysis and control of disqualified mechanical properties of Q235B hot rolling thick steel plate
HU Li;,ZHAO Yong-feng;,LIN Xiao-gang;,LIU Yong-gang;,LIAO Li;
HU Li;,ZHAO Yong-feng;,LIN Xiao-gang;,LIU Yong-gang;,LIAO Li;
..............page:46-49
Analysis of soft point defects on 65Mn steel after quenching
SUN Yi-qiang;,HAN Bin;
SUN Yi-qiang;,HAN Bin;
..............page:50-53
Analysis of cracking of reducer gear shaft
ZHANG Yan-wen;,ZHANG You-deng;,YANG Zhi-ting;,TAO Yong;
ZHANG Yan-wen;,ZHANG You-deng;,YANG Zhi-ting;,TAO Yong;
..............page:54-57
Development trend of laboratory design in inspection and analysis system of iron and steel industry
KUANG Jun;,WANG Yan;
KUANG Jun;,WANG Yan;
..............page:58-61