Journal of Aerospace Power 2010 Issue 1 Comparison of characteristics of ramjet with cavity-based flameholder and V-gutter flameholder

Comparison of characteristics of ramjet with cavity-based flameholder and V-gutter flameholder
LI Qing;PAN Yu;TAN Jian-guo;WANG Zhen-guo

..............page:35-40

Effects of dynamic load on the heat transfer characteristics of two-phase pipe boiling flow
YAO Qiu-ping;SONG Bao-yin;ZHAO Mei

..............page:28-34

Improvement on S-A model for compressor flow based on turbulence transport nature
WANG Dan-hua;LU Li-peng;LI Qiu-shi

..............page:80-86

Basic parameters analysis of first stage engine system for heavy lift vehicle
LI Xiang-ning;LIU Yu

..............page:180-186

Numerical investigation of the effect of thermo physical properties on the performance of heat storage system
WU Bin;XING Yu-ming;RUI Shou-zhen

..............page:47-52

FEM/BEM combined model for prediction of sound propagation and radiation of a duct inlet
REN Zhi-wen;HOU Wei;DU Lin;JING Xiao-dong

..............page:136-141

Method of predicted fatigue life of aero-engine\'s principal shaft
LU Shan;CHEN Qian;CHEN Jun

..............page:148-151

Mistuning characteristics analysis of mistuned bladed disk assemblies
LIAO Hai-tao;WANG Jian-jun;LI Qi-han

..............page:160-168

Regression analysis method for type-Ⅰcensored data
FU Hui-min;YUE Xiao-rui

..............page:142-147

Real-time simulation model for a turbofan engine based on nonlinear system equilibrium manifold theory
HU Wei-hong;LI Shu-qing;SUN Jian-guo

..............page:213-217

Effect of backpressure on the film thickness inside liquid swirl injector
CHEN Xiao-dong;LIU Yu;YANG Vigor

..............page:198-202

Analysis of flight stability and rear flow field of the cargo projectile
LI Jian-ping;BAI Chun-hua

..............page:107-113

Performance analysis and parameters optimization of fly-like aircraft
HU Ming-lang;WEI Rui-xuan;SONG Min;LI Xia;GUO Qing;LIU Yue

..............page:114-122

Pressure measurements on a static disk with high positioned inflow and radial outflow under rotor-stator system
QUAN Yong-kai;SUN Ji-ning;LUO Xiang

..............page:53-57

Hybrid RANS/LES simulation of mass exchange characteristics of cavity for supersonic combustion
WANG Hong-bo;SUN Ming-bo;WU Hai-yan;WANG Zhen-guo

..............page:41-46

General-structural design study of a micro turbojet engine
CHEN Wei;DU Fa-rong;DING Shui-ting;LI Yun-qing

..............page:169-174

Experimental study of the mechanism of improving stall margin of low speed axial-flow compressor with micro-injection under rotating inlet distortion
ZHANG Jing-xuan;LUO Ma;NIE Chao-qun;LIN Feng;CHEN Jing-yi

..............page:67-71

Numerical simulations of upstream wake-tip leakage vortex interactions in turbine rotor
ZOU Zheng-ping;QI Lei;LI Wei;LIU Huo-xing

..............page:58-66

Tooth surface design and manufacture for arcuate tooth trace face-gear
FANG Zong-de;CAO Xue-mei;SHEN Yun-bo

..............page:224-227

Fault diagnosis based on underdetermined blind source separation using potential energy function
ZHANG Yun;LI Ben-wei;WANG Yong-hua

..............page:218-223

Bayesian analysis for the power law process based on Markov Chain Monte Carlo
WANG Yan-ping;L(U) Zhen-zhou;ZHAO Xin-pan

..............page:152-159

Numerical simulation of active suppression of rotating stall in axial compression systems
YU Lan-lan;HU Jun;TU Bao-feng;WANG Zhi-qiang

..............page:92-101

Flow and heat transfer characteristics in a periodical changeable cross-section micro-channel heat sink
XIA Guo-dong;XU Zhi-bo;QI Jing-zhi

..............page:6-10

Thermal design method of temperature control for regenerative cooling panel
XIA Xin-lin;AI Qing

..............page:1-5

hang kong dong li xue bao zheng gao jian ze

..............page:封3

Dual engine control strategy for an unmanned helicopter
SHENG Shou-zhao;WANG Dao-bo;JIANG Bin;ZHAO Chao

..............page:208-212

Research on selection of measurement parameters of engine fault diagnosis based on primary factor model
SUN Xiang-feng;CHEN Yu-chun;HU Fu

..............page:129-135

Research on optimal operator of blade edge detection from computed tomography images based on computational theory
SUN Jing-jing;YANG Min;LIU Jing-hua

..............page:175-179

Gear fault diagnosis based on wavelet and neural network
LI Yong-long;SHAO Ren-ping;XUE Teng

..............page:234-240

Improvement of an engine lubricating oil heat diffusion system
CHEN Wei-jian;ZHANG Da-lin;MENG Fan-xin

..............page:18-22

Experimental study of the flow structures of the concave surface with inclined impingement in limited space
MAO Jun-kui;MIU Guo-jun;LIU Zhen-xiong

..............page:11-17

Simulation of radiant heat flux of rocket engine exhaust plume on lunar detector
SHI Liang-chen;ZHU Ding-qiang;XU Xu;CAI Guo-biao

..............page:187-192

Application of Kriging model to reliability analysis of solid rocket motor grain
LIU Ji-tao;LIU Fei;ZHANG Wei-hua

..............page:193-197

Performance optimization for finger seal based on fuzzy Nash equilibrium game
ZHANG Yan-chao;CHEN Guo-ding;SHEN Xiao-long

..............page:228-233

zhi xie shen gao ren

..............page:241-242

Experimental study on outlet temperature field for combustor of heavy-duty gas turbine
LIU Kai;ZHANG Bao-cheng;CAI Jiu-ju;MA Hong-an

..............page:23-27

Shear-modified sub-grid model and its applications to turbulent channel flow
XIAO Hong-lin;LUO Ji-sheng

..............page:123-128

Study on turbine aerodynamics design of small turbofan engines
ZHANG Wei-hao;ZOU Zheng-ping;LIU Huo-xing;LI Wei

..............page:72-79

Numerical simulation method for stochastic fluctuation of inlet total pressure
WANG Zhi-qiang;HU Jun;LI Liang;JIANG Da-zhi;ZHAO Yun-sheng

..............page:87-91

Fault diagnosis system based on knowledge pushing
YANG Si-feng;WANG Qi;LIU Lu

..............page:203-207

Predictions of dynamic damping coefficients of basic finner based on CFD
TAO Yang;FAN Zhao-lin;ZHAO Zhong-liang

..............page:102-106