Journal of Aerospace Power 2008 Issue 10 Internal ballistics calculation of solid rocket motor under high overload

Internal ballistics calculation of solid rocket motor under high overload
GUO Yan-hong;LIANG Xiao-geng;CHEN Bin

..............page:1944-1948

Experimental investigation on once injecting water in metal fuel/water ramjet
hu fan ; zhang wei hua ; xia zhi xun ; hu jian xin ; li shi liang ; huang li ya

..............page:1949-1952

jian xun

..............page:封3,1858,1948

Vibration fault diagnosis method based on gray level-gradient co-occurrence matrix for rotating machinery
DOU Wei;LIU Zhan-sheng;WANG Zheng-xian

..............page:1939-1943

Analysis of data mining of clustering and its application to mechanical transmission fault diagnosis
SHAO Ren-ping;HUANG Xin-na;HU Jun-hui

..............page:1933-1938

Tooth contact analysis of face gear drive with helical pinion and simulation of the tooth face
zhao ning ; zeng xiao chun ; guo hui ; shen yun bo ; fang zong de ; wei bing yang

..............page:1927-1932

Reusable launch vehicle pitch attitude control system research by trajectory linearization
SUN Chun-zhen;HUANG Yi-min;GUO Suo-feng

..............page:1921-1926

New intelligent neural network adaptive control scheme research for aeroengine
ZHAO Jun;CHEN Jian-jun;WANG Ling-gang

..............page:1913-1920

Numerical optimization of transonic axial compressor by bowed blades
zhang xiao dong ; wu hu ; huang jian ; ma cong hui

..............page:1908-1912

Design of transonic centrifugal compressor for vehicle
zheng xin qian ; zhang yang jun ; guo gong da ; zhang ji zhong

..............page:1903-1907

Numerical simulation of the flow-field and performance of a micro-flowrate centrifugal compressor impeller
hua yan hong ; yuan wei xing ; yuan xiu gan ; yang chun xin ; chen jiang

..............page:1896-1902

Thrust analysis and experimental study of the flexible wings of a flapping-wings aircraft
XU Yi-cun;BI Shu-sheng;ZONG Guang-hua

..............page:1892-1895

Comparison of four turbulence models in diffusing S-duct
ZHANG Li-fen;LIU Zhen-xia;L(U) Ya-guo

..............page:1888-1891

Numerical simulation of helicopter rotor-fuselage-engine aerodynamic interactions
HU Li;CAO Yi-hua;ZHAO Ming

..............page:1882-1887

Normal mode analysis for the sound propagation in a lined annular duct with mean swirling flow
GUAN Ying;WANG Tong-qing;ZHAO Xiao-jian

..............page:1875-1881

Research on aeroengine performance margin design considering performance deterioration in utility
ZHOU Mao-jun

..............page:1868-1874

Numerical simulation of the flowfield around the seat/occupant system
song bao yin ; zhang zhong gang ; mou jie ; yao qiu ping

..............page:1859-1867

Modeling behavior of cross-ply ceramic matrix composites under quasi-static loading
xu ren hong ; song ying dong ; li long biao ; sun zhi gang

..............page:1854-1858

Dynamic response of damped gyroscopic system with complex modal method
ZENG Liang;LI Lin

..............page:1847-1853

Aeroengine fault diagnosis based on variable precision rough sets
suo zhong ying ; zhu lin hu ; wu hua ; su qiang

..............page:1842-1846

Damage failure analysis for composite bolted joints with tightening torque subjected to static loadings
WANG Dan-yong;WEN Wei-dong

..............page:1835-1841

Design and experimentation of simulation specimen for aero-engine compressor disk slot used in low cycle fatigue test
yang xing yu ; dong li wei ; geng zhong xing ; liu xin ling ; zhao fu xing

..............page:1829-1834

Research on a smoothing method for engine removal rate
bai fang ; zuo hong fu ; ren shu hong ; shen shi song ; geng duan yang

..............page:1821-1828

Experiments on dynamic response of labyrinth air seals with damping-ring/sleeves
ZENG Liang;LI Lin

..............page:1813-1820

Torsional vibration analysis of helicopter power transmission system by the multi-shaft transfer matrix method
wang jian jun ; mao zhen zhong ; qing li wei ; li qi han

..............page:1805-1812

Investigation of the wall temperature distribution and cooling efficiency for impingement/effusion cooling scheme
hu chao ; xu quan hong ; xu jian ; lin yu zhen

..............page:1800-1804

Application of nanofluid in thermal performance enhancement of horizontal screen heat pipe
SHU Tao;LIU Zhen-hua

..............page:1795-1799

Experimental research on the cooling characteristics of an afterburner fuel injector with double-wall construction
zuo bao hua ; fan wei jun ; li rui ming ; yang mao lin

..............page:1788-1794

Design and study of annular combustor for micro-turbine engine
LI Cong;FANG Shu-zhou;ZHANG Ping

..............page:1783-1787

Combustion characteristics of self-stabilized dual-swirler cup in the unconfined case
ZHANG Chi;WANG Zhi-qiang;LIN Yu-zhen

..............page:1778-1782

Numerical investigation on improvement of film cooling effectiveness with console hole
YAO Yu;ZHANG Jing-zhou;ZHOU Nan

..............page:1772-1777

Improved simulation of electrothermal de-icing system
chang shi zuo ; ai su xiao ; huo xi heng ; yuan xiu gan

..............page:1753-1758

Numerical studies of the effects of shaped holes on cooling effectiveness of flat plate film with conical shrink entrance and conical diffuser exit
LI Zhi-qiang;TIAN Tao

..............page:1759-1764

Film cooling experiment of row of expanded shape holes
yang cheng feng ; zhang jing zhou ; chen li qiang ; wu shi xun

..............page:1765-1771